Highpoint RocketRAID 2302 Podręcznik Użytkownika Strona 18
- Strona / 81
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Note: Many server-level chassis include hard-disk hot-swap bays. For these
system chassis, cables are attached to the chassis backplane, rather than
directly to each individual hard disk. Consult the chassis’s manual for proper
installation procedures.
5. Close and secure the system chassis.
4 - Verifying Installation
Once the host adapter and hard disks have been installed into the chassis, boot-up
the system to verify that the hardware is properly recognized.
1. Power on the system. If the system detects the presence of the adapter, the
RocketRAID BIOS Utility will be displayed during bootup.
2. Press Ctrl+H to access the RocketRAID adapter’s BIOS Utility.
The BIOS Utility will display information about hard disks attached to the adapter.
Make sure all attached disks are detected by this utility. If any of the hard disks are
not detected, power down the system and check the power and SATA cable
connections.
RocketRAID 230x Hardware Description/Installation
2-8
- RocketRAID 230x 1
- SATAII Host Adapter 1
- Copyright 2
- Trademarks 2
- Table of Contents 3
- Chapter 1 5
- Introduction 5
- About this Guide 6
- Adapters 6
- Disk initialization 7
- Disk Status 7
- Array initialization 8
- Foreground initialization 8
- Background initialization 8
- Online RAID Level Migration 9
- Spare disk 9
- Legacy disk 9
- Supports RR1640 RAID arrays 9
- Chapter 2 10
- RocketRAID 2300 11
- RocketRAID 2302 12
- 2 - LED Connections 13
- 4: D4 14
- 5: +3.3V 14
- 1: D1 14
- 2: D2 14
- 3: D3 14
- LED Connections – RR2304 16
- LED Connections – RR2302 16
- 4 - Verifying Installation 18
- Chapter 3 19
- RocketRAID 230x BIOS Utility 19
- RocketRAID BIOS Utility 20
- 1 - BIOS Command Overview 20
- 2 - Creating RAID Arrays 22
- 3 - Adding/Remove Spare Disks 23
- 4 - Updating the BIOS 24
- Chapter 4 29
- Driver and Software CD 30
- To install the RAID software: 32
- Windows Driver Installation 33
- Overview 34
- 3 - Creating an Array 37
- 4 - Deleting an Array 39
- 5 - Configuring Spare Disks 39
- Verifying an Array 40
- 7 – OCE/ORLM 41
- Device Management 42
- Changing Device Settings 42
- S.M.A.R.T Status 42
- SAF-TE Management 43
- Renaming an Array 43
- 9 - Managing Events 44
- Managing Tasks 45
- Add a Scheduled Task 46
- Linux Driver Support 47
- Modify a Scheduled Task 48
- Delete a Scheduled Task 48
- Add a Connection 49
- Modify a Connection 49
- Delete a Connection 50
- Connect to a Remote System 50
- Disconnect Remote System 51
- System Configuration 51
- Add a User 53
- Delete a User 54
- Set Password 54
- Set Privilege 54
- Chapter 5 56
- Host Adapter 57
- 4 - Updating the Driver 60
- 5 - Uninstalling the Driver 60
- Existing System 62
- Step 1 Update Grub 68
- 4 – Updating the Driver 70
- Chapter 6 71
- FreeBSD Driver Support 71
- Step 2 Install FreeBSD 72
- <-press SPACE key 73
- Step 1 Copy the Driver Module 75
- For FreeBSD 5.x: 76
- Step 2 Test the Driver Module 76
- 3 - Updating the Driver 78
- 4 – Uninstalling the Driver 78
- Appendix 79
- Customer Support 79
Powiązane produkty i podręczniki dla Kontrolery urządzeń peryferyjnych Highpoint RocketRAID 2302
(60 strony)Worx WU303.1 900W Hammer Drill 240V. 2 Speed 13mm Keyle podręczniki
Instrukcje obsługi i podręczniki użytkownika dla Elektronarzędzia Worx WU303.1 900W Hammer Drill 240V. 2 Speed 13mm Keyle.
Dostarczamy 1 pdf podręczników Worx WU303.1 900W Hammer Drill 240V. 2 Speed 13mm Keyle do pobrania za darmo według typów dokumentów: Instrukcja Użytkownika
Komentarze do niniejszej Instrukcji